How to Replace a Tub Yourself: Removing and also Replacing.
How to Replace a Tub Yourself: Removing and also Replacing.
Blog Article
Just how do you actually feel in regards to Tools You Need to Install a New Bathtub ?
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is easily accessible, the job can move immediately; if you need to open up a wall to remove the old tub and position the new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub and set in the new one. Make certain you have actually certified yourself for the job as well as are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to take into consideration employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your restroom if you have actually currently acquired a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washers are in location in between the faucet and the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the called for placement. The wooden boards are handy in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water and inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the tub and likewise inspect the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been made use of at the very least once as this will settle it into its last placement.
Planning for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, causing difficulties with dampness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes and cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealer can split fairly early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on How to Install a Bathtub, I imagined sharing that segment was important. For those who enjoyed our post if you please do not forget to share it. Thank-you for your time spent reading it.
Maintenance Sign-Up Report this page